View FTRJ1519P1WNL_1233383.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? finisar corporation april 11, 2005 rev c page 1 product specification 2 gigabit long-wavelength pluggable sfp transceiver ftrj1519p1xnl product features ? up to 2.125gb/s bi-directional data links ? hot-pluggable sfp footprint ? built-in digital diagnostic functions ? uncooled 1550nm dfb laser transmitter ? duplex lc connector ? very low jitter ? metal enclosure, for lower emi ? single 3.3v power supply ? up to 80 km on 9/125 m smf ? low power dissipation typically <700mw ? extended operating temperature range: -5c to 85c applications ? gigabit ethernet ? 1x and 2x fibre channel finisar?s ftrj1519p1xnl small form factor pluggable (sfp) transceivers are compatible with the small form factor pluggable multi-sourcing agreement (msa). they simultaneously comply with gigabit ethernet as specified in ieee std 802.3, and 1x and 2x fibre channel as defined in fc-pi 13.0. digital diagnostics functions are available via the 2-wire serial bus specified in the sfp msa. product selection ftrj1519p1xnl x w wide extraction bail b narrow extraction bail
ftrj1519p1xnl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 2 i. pin descriptions pin symbol name/description ref. 1 v eet transmitter ground (common with receiver ground) 1 2 t fault transmitter fault. not supported. 3 t dis transmitter disable. laser output disabled on high or open. 2 4 mod_def(2) module definition 2. data line for serial id. 3 5 mod_def(1) module definition 1. clock line for serial id. 3 6 mod_def(0) module definition 0. grounded within the module. 3 7 rate select no connection required 4 8 los loss of signal indication. logic 0 indicates normal operation. 5 9 v eer receiver ground (common with transmitter ground) 1 10 v eer receiver ground (common with transmitter ground) 1 11 v eer receiver ground (common with transmitter ground) 1 12 rd- receiver inverted data out. ac coupled 13 rd+ receiver non-inverted data out. ac coupled 14 v eer receiver ground (common with transmitter ground) 1 15 v ccr receiver power supply 16 v cct transmitter power supply 17 v eet transmitter ground (common with receiver ground) 1 18 td+ transmitter non-inverted data in. ac coupled. 19 td- transmitter inverted data in. ac coupled. 20 v eet transmitter ground (common with receiver ground) 1 notes : 1. circuit ground is internally isolated from chassis ground. 2. laser output disabled on t dis >2.0v or open, enabled on t dis <0.8v. 3. should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0v and 3.6v. mod_def(0) pulls line low to indicate module is plugged in. 4. finisar ftrjxx21xxxxx transceivers operate between oc-3 and oc-48, 1x and 2x fibre channel, and gigabit ethernet data rates and respective protocols without active control. finisar ftrjxx19xxxxx transceivers operate at 1x and 2x fibre channel, and gigabit ethernet data rates and respective protocols without active control. 5. los is open collector output. should be pulled up with 4.7k ? 10 kohms on host board to a voltage between 2.0v and 3.6v. logic 0 indicates normal operation; logic 1 indicates loss of signal. veet veet veer veer td- td+ rd+ rd- vcct vccr veet veer txfault mod-def(2) mod-def(1) mod-def(0) rate select los 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 towards asic towards bezel tx disable veer pinout of connector block on host board
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 3 ii. absolute maximum ratings parameter symbol min typ max unit ref. maximum supply voltage vcc -0.5 4.5 v storage temperature t s -40 85 c case operating temperature t op -5 85 c relative humidity rh 0 85 % 1 iii. electrical characteristics (t op = -5 to 85 c, v cc = 3.00 to 3.60 volts) parameter symbol min typ max unit ref. supply voltage vcc 3.15 3.60 v supply current icc 200 300 ma transmitter input differential impedance r in 100 ? 2 single ended data input swing vin,pp 250 1200 mv transmit disable voltage v d vcc ? 1.3 vcc v transmit enable voltage v en vee vee+ 0.8 v 3 transmit disable assert time 10 us receiver single ended data output swing vout,pp 300 400 800 mv 4 data output rise time t r 100 175 ps 5 data output fall time t f 100 175 ps 5 los fault v los fault vcc ? 0.5 vcc host v 6 los normal v los norm vee vee+0.5 v 6 power supply rejection psr 100 mvpp 7 deterministic jitter contribution rx ? dj 51.7 ps 8 total jitter contribution rx ? tj 122.4 ps notes : 1. non condensing. 2. connected directly to tx data input pins. ac coupled thereafter. 3. or open circuit. 4. into 100 ohms differential termination. 5. 20 ? 80 % 6. loss of signal is lvttl. logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. receiver sensitivity is compliant with power supply sinusoidal modulation of 20 hz to 1.5 mhz up to specified value applied through the recommended power supply filtering network. valid on receive side for input powers within receive sensitivity. 8. measured with dj-free data input signal. in actual application, output dj will be the sum of input dj and ? dj.
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 4 iv. optical characteristics (t op = -5 to 85 c, v cc = 3.00 to 3.60 volts) parameter symbol min typ max unit ref. transmitter output opt. pwr: 9/125 smf p out 0 5 dbm 1 optical wavelength 1540 1570 nm 2 spectral width (-20db) 1 nm 2 optical extinction ratio er 9 db optical modulation amplitude oma 174 w 2,3 sidemode supression ratio ssr min 30 db optical rise/fall time t r / t f 180 ps 4 relative intensity noise rin -120 db/hz deterministic jitter contribution rx ? dj 51.7 ps 5 total jitter contribution rx ? tj 122.4 ps receiver average rx sensitivity @ 2.125 gb/s (2x fibre channel) r sens1 -21 dbm 6, 7 average rx sensitivity @ 1.25 gb/s (gigabit ethernet) r sens2 -22 dbm 6, 7 average rx sensitivity @ 1.06 gb/s (1x fibre channel) r sens1 -22 dbm 6, 7 stressed rx sens. =1.25 gb/s -18 -14.5 dbm average received power rx max 0 dbm receiver elec. 3 db cutoff freq. 1500 mhz optical center wavelength c 1270 1600 nm return loss 12 db los de-assert los d -23 dbm los assert los a -32 dbm los hysteresis 0.5 db notes : 1. class 1 laser safety per fda/cdrh and en (iec) 60825 regulations. 2. meets curves in fc-pi 13.0 figures 18 and 19, which allow trade-off between wavelength, spectral width and oma. 3. equivalent extinction ratio specification for fibre channel. allows smaller er at higher average power. 4. unfiltered, 20-80%. complies with ieee 802.3 (gig. e), fc 1x and 2x eye masks when filtered. 5. measured with dj-free data input signal. in actual application, output dj will be the sum of input dj and ? dj. 6. measured with conformance signals defined in fc-pi 13.0 specifications. 7. measured with prbs 2 7 -1 at 10 -12 ber
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 5 v. general specifications parameter symbol min typ max units ref. data rate br 1062 2125 mb/sec 1 bit error rate ber 10 -12 2 max. supported link length on 9/125 m smf @ 2x fibre channel l max1 76 km 3, 4 max. supported link length on 9/125 m smf @ gigabit ethernet l max2 88 km 3, 4 notes : 1. gigabit ethernet and 1x/2x fibre channel compliant. 2. tested with a prbs 2 7 -1 test pattern. 3. dispersion limited per fc-pi rev. 13 4. attenuation of 0.25 db/km is used for the link length calculations. distances are indicative only and are calculated solely on link budget. a 2db penalty is included for dispersion on >2gb/s data rates. please refer to the optical specifications in table iv to calculate a more accurate link budget based on specific conditions in your application. vi. environmental specifications finisar 1550nm sfp transceivers have an extended operating temperature range from ?5c to +85c case temperature. parameter symbol min typ max units ref. case operating temperature t op -5 85 c storage temperature t sto -40 85 c vii. regulatory compliance finisar transceivers are class 1 laser products and comply with us fda regulations. these products are certified by tv and csa to meet the class 1 eye safety requirements of en (iec) 60825 and the electrical safety requirements of en (iec) 60950. copies of certificates are available at finisar corporation upon request. copies of the referenced certificates are available at finisar corporation upon request.
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 6 viii. digital diagnostic functions finisar ftrj1519p1xnl sfp transceivers support the 2-wire serial communication protocol as defined in the sfp msa 1 . it is very closely related to the e 2 prom defined in the gbic standard, with the same electrical specifications. the standard sfp serial id provides access to identification information that describes the transceiver?s capabilities, standard interfaces, manufacturer, and other information. additionally, finisar sfp transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. it also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. the sfp msa defines a 256-byte memory map in e 2 prom that is accessible over a 2-wire serial interface at the 8 bit address 1010000x (a0h). the digital diagnostic monitoring interface makes use of the 8 bit address 1010001x (a2h), so the originally defined serial id memory map remains unchanged. the interface is identical to, and is thus fully backward compatible with both the gbic specification and the sfp multi source agreement. the complete interface is described in finisar application note an- 2030: ?digital diagnostics monitoring interface for sfp optical transceivers?. the operating and diagnostics information is monitored and reported by a digital diagnostics transceiver controller (ddtc) inside the transceiver, which is accessed through a 2-wire serial interface. when the serial protocol is activated, the serial clock signal (scl, mod def 1) is generated by the host. the positive edge clocks data into the sfp transceiver into those segments of the e 2 prom that are not write-protected. the negative edge clocks data from the sfp transceiver. the serial data signal (sda, mod def 2) is bi-directional for serial data transfer. the host uses sda in conjunction with scl to mark the start and end of serial protocol activation. the memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. for more information, please see the sfp msa documentation 1 or finisar application note an-2030. digital diagnostics for the ftrj1519p1xnl are externally calibrated by default. please note that evaluation board fdb-1018 is available with finisar moddemo software that allows simple to use communication over the 2-wire serial interface.
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 7 ix. mechanical specifications finisar?s oc-48/stm-16 small form factor pluggable (sfp) transceivers are compatible with the dimensions defined by the sfp multi-sourcing agreement (msa). ftrj1519p1bnl
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 8 FTRJ1519P1WNL
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 9 x. pcb layout and bezel recommendations
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 10
ftrj1519p1xcl pluggable sfp product specification ? april 2005 ? finisar corporation april 11, 2005 rev c page 11 xi. references 1. ?fibre channel physical and signaling interface (fc-ph, fc-ph2, fc-ph3)?. american national standard for information systems. 2. ?fibre channel draft physical interface specification (fc-pi 13.0)?. american national standard for information systems.(*) 3. small form factor pluggable (sfp) transceiver multi-source agreement (msa), september 2000. documentation is currently available at finisar upon request. 4. ieee std 802.3. ieee standards department, 2002. (*) neither ieee 802.3 nor fc-pi 13.0 specifies a 1550nm dfb single mode interface. the ftrj1519p1xnl complies with these standards except for receiver sensitivity, and transmit output power. see section iv for details. xii. for more information finisar corporation 1308 moffett park drive sunnyvale, ca 94089-1133 tel. 1-408-548-1000 fax 1-408-541-6138 sales@finisar.com www.finisar.com

▲Up To Search▲

Price & Availability of FTRJ1519P1WNL

	To Download FTRJ1519P1WNL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .